Plasma Cutter - 55 A - 230 V - 17 mm

Manufacturer: Stamos Selection | item number: EX10020043 | Model: S-PLASMA 55H / SPAWARKA

Plasma Cutter - 55 A - 230 V - 17 mm
Plasma Cutter - 55 A - 230 V - 17 mm
Plasma Cutter - 55 A - 230 V - 17 mm
Plasma Cutter - 55 A - 230 V - 17 mm
Plasma Cutter - 55 A - 230 V - 17 mm
Plasma Cutter - 55 A - 230 V - 17 mm
Plasma Cutter - 55 A - 230 V - 17 mm
Play Video
360° photo
Tap to open gallery
419.00

Prices incl. VAT

  • Free shipment to Ireland

    ?

    This product is currently not available.

  • 30 days return service

    ?
  • 3 years guarantee

Product highlights

  • Cutting current: 10 - 55 A
  • Cutting capacity up to 17 mm
  • Cutting kerf width: 1 mm
  • Digital display
  • 230 V

The compactly-built plasma cutter from Stamos Selection weighs less than 10 kg, making it an attractive option for mobile use. With an operating voltage of 230 volts, the power unit provides a variable cutting current. In the range between 10 and 55 amps, the cutting current can be infinitely adjusted to the specific requirements of each individual application.

Show more Show less

The cutter has some power reserves, which are sufficient for cuts in metal up to 17 millimetres thick. You can cut ordinary tool steel as well as high-alloy special steels. The S-Plasma-55H also makes short work of non-ferrous metals like aluminium, copper and titanium. The issue of material waste can practically be ignored thanks to the cutting width of just one millimetre.

Show more Show less

The 5 meter long plasma hose in connection with the 4 meter long compressed air supply line ensures sufficient freedom of movement during work. The plasma torch comes with plenty of accessories, including pressure reducer along with pressure gauge for checking the compressed air values. You can choose the external compressor according to your requirement and circumstances, and adjust the air pressure via the external pressure reducer. Thus, the device proves to be very flexible and easy to transport. 

Show more Show less

To prevent undesirable deformations or chemical reactions at the edges after the cutting process is completed, the compressed air continues to flow for a defined interval. On the power unit, the post-flow time can be conveniently set between 2 and 10 seconds by means of a controller.

Show more Show less

In addition to the post-flow time, the cutting current can also be infinitely adjusted on the power unit. You can check the values on the easy-to-read LED display on the front. Another indicator light signals overheating or other malfunctions.

Show more Show less

To prevent overheating and the associated possible consequential damage, the base unit is equipped with a powerful air cooling system. If, in the worst case, the appliance still heats up excessively, the overheat protection will take effect. Another product feature designed for robustness and durability is the resilient housing made of coated steel sheet.

Show more Show less

The compact design and light weight of less than 10 kg make it possible to use the plasma cutter even in hard-to-reach areas with limited space. You can carry this powerful electrical device by a sturdy metal handle.

Show more Show less

  • Impressive performance values: 55 amps at 60 percent duty cycle
  • Cut metallic materials up to 17 millimetres thick
  • Generous 5 metre-long plasma hose
  • Performance control thanks to clear LED displays
  • Comes with UK plug

Plasma Cutter - 55 A - 230 V - 17 mm

The S-Plasma 55H plasma cutter from Stamos Selection convinces with its balanced technical basic parameters and its ease of use. The plasma cutter works cost-effectively and straightforwardly with compressed air and is the ideal helper for all metal work in automotive workshops and in commercial and industrial businesses. It also provides active support to do-it-yourselfers in their private repairs and renovations. The plasma cutter is the ideal tool for cutting all types of metals.

Model
S-PLASMA 55H
Condition
New
Function
Plasma cutting
Input voltage
230 V
Input frequency
50 Hz
Rated input current
22,8 A
Max. input current
32,2 A
Rated input power
5 kVA
Max. input power
7,1 kVA
Open circuit voltage
230 V
Cutting current
10 - 55 A
Operating time (duty cycle)
60 %
Cutting current at 100% duty cycle
42,6 A
Cutting current at 60% duty cycle
55 A
Air post-flow time
2 - 10 sec
Ignition
Contact
Housing cooling
Fan
Torch cooling
Air
Length, grounding cable
4 m
Length, plasma cable
5 m
Length, compressed air hose
4 m
Length, power cable
2,5 m
Max. cutting depth
17 mm
Cutting depth for high-quality cuts
8-15 mm
Cutting width
1 mm
Air flow rate
175 L/min
Required air pressure
4,5 bar
Insulation class
F
Protection class
IP21
Dimensions (LxWxH)
44 x 31 x 17 cm
Weight
9,01 kg
Shipping dimensions (LxWxH)
52 x 38 x 38 cm
Shipping weight
13,5 kg
Technical drawing
Delivery Package
  • Plasma cutter S-PLASMA 55H
  • Plasma cable assembly with torch: 4 m
  • Air hose: 4 m
  • Grounding cable: 4 m
  • 2 cutting nozzles
  • 2 electrodes
  • Ceramic cap and swirl ring for plasma
  • Pressure gauge and pressure regulator
  • Gas hose
  • 2 clamp rings
  • Allen key
  • Instruction manual
 
IGBT

IGBT = insulated-gate bipolar transistor. IGBT is a bipolar transistor with an insulated gate electrode. This semi-conducting device is being increasingly used in power electronics because it combines the advantages of two transistor types: the easy controls of the field effect transistor and the fast switching and high breakdown voltage of the bipolar transistor. The IGBT also offers some robustness against short circuits because it limits the electrical continuity. IGBTs are a further development of MOSFET technology.

Show moreShow less
 
VENTILATORS

Powerful fans ensure an optimal removal of heat from the unit.

 
GAS/AIR CONNECTION

For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection.

Show moreShow less
 
EARTHING SYSTEM

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

 
GROUND TERMINAL CONNECTOR

 

 
CUTTING TORCH CONNECTION

 

 
SUPPLY VOLTAGE

This device works with a 1-phase connection (230 V +/- 10 %).

 
WELDING CURRENT

 

 
GAS POST-FLOW TIME

The time after the weld is finished in which gas continues to flow from the torch; this cools the burner and protects the weld from oxidation.

 
2-STROKE

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

 
PLASMA CUTTING

The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.

 
POWER SWITCH

 

 
DISPLAY

Shows the welding / cutting parameters.

 
OVERLOAD / FAULT LED

The LED light indicates overheating or a malfunction.

 
PRESSURE GAUGE (MANOMETER)

Shows the value of compressed air the compressor delivers to the plasma cutter. The plasma cutter has a pressure reducing valve which regulates the air pressure.

The diverse assortment of products from Stamos enable you to cut or join materials efficiently and precisely. Our portfolio ranges from professional soldering stations to top-class welding machines and precise plasma cutters, to the matching accessories. Let us demonstrate to you the functionality, quality and versatility – not to mention the cost-effectiveness – of our professional line. Our videos show our products in action.

What's the maximum thickness of material the plasma cutter can cut through?

The maximum thickness is 17 mm.

How does the device inform me when it's threatening to overheat?

A diode lights up as soon as the maximum duty cycle is exceeded and the device heats up too much as a result. The light will also warn you if the plasma cutter generates too much heat due to malfunction. In both cases, the operation should be interrupted.

5 Based on 5 reviews

Sort by...

Leave a review (5 stars is highest, 1 is lowest)
Click on the link sent to your e-mail address and confirm your opinion! It will be published after verification.

The fields marked with * are required.

Reviews from Anonym (30 Mar 2022)
Reviews from Anonym (30 Mar 2022) sehr gut

Sehr gutes Produkt, empfehlenswert.

Reviews from Wilhelm Markus (5 Mar 2022)
Reviews from Wilhelm Markus (5 Mar 2022) sehr gut

bin bis jetzt sehr zufrieden, empfehlenswert.

Reviews from Roland (21 Nov 2021)
Reviews from Roland (21 Nov 2021) Good price

Very good price and a good pruduct

Reviews from Anonym (28 Feb 2021)
Reviews from Anonym (28 Feb 2021) sehr gut

die maschine funktioniert sehr gut. aber bei materialstärken über 10 mm gibt es kaum saubere schnitte.

Reviews from Einar Røen (11 Aug 2020)
Reviews from Einar Røen (11 Aug 2020) Plasmacutter, min første.

Har så vidt begynt og bruke den, hendig maskin . Den skjærer godt: Skulle hatt bruksanvisning på norsk, Ser ut til at maskinen blir uunnværlig.
Hilsen Einar Røen

expondo expert

Still not sure?

Our experts are ready to help!
+44 20 376 988 02
Mon - Fri 09:00am - 04:00pm
Schweißhelm – Legend– PROFESSIONAL SERIES - 2985 - 1
95.00€
Prices incl. VAT plus shipping costs
This product
  • Cutting current: 10 - 55 A
  • Cutting capacity up to 17 mm
  • Cutting kerf width: 1 mm
  • Digital display
  • 230 V

This product is currently not available.

Plasma Cutter - 55 A - 230 V - 17 mm

Plasma Cutter - 55 A - 230 V - 17 mm

(5)
419.00€  

This product is currently not available.

  • Cutting current: 10 - 55 A
  • Cutting capacity up to 17 mm
  • Cutting kerf width: 1 mm
  • Digital display
  • 230 V
  • Cutting current: 10 - 50 A
  • Duty cycle: 60 %
  • Cutting depth: 15 mm
  • LED display
  • 230 V

Ready to ship today,
Delivery time appr. 4-7 workdays

Plasma Cutter - 50 A - 230 V - Basic

Plasma Cutter - 50 A - 230 V - Basic

(4)
Instead of: 429.00€   319.00€  

Ready to ship today,
Delivery time appr. 4-7 workdays

  • Cutting current: 10 - 50 A
  • Duty cycle: 60 %
  • Cutting depth: 15 mm
  • LED display
  • 230 V