Plasma Cutter - 90 A - 400 V
679.00 Prices incl. VAT plus shipping costs*

Plasma Cutter - 90 A - 400 V

Manufacturer: Stamos Power ² | item number: EX10020129 | Model: S-CUTTER 90 / PRZECINARKA CUT 90

Plasma Cutter - 90 A - 400 V
Plasma Cutter - 90 A - 400 V
Plasma Cutter - 90 A - 400 V
Plasma Cutter - 90 A - 400 V
Plasma Cutter - 90 A - 400 V
Play Video
360° photo
Tap to open gallery
679.00

Prices incl. VAT plus shipping costs*

  • Free shipment to Ireland

    ?

    Ready to ship today,
    Delivery time appr. 4-6 workdays

  • 30 days return service

    ?
  • 3 years guarantee

Ready for immediate shipping When ordering and making payment within the next 4 hours 18 mins , shipping will happen today.

Product highlights

  • Cutting current: 20 - 90 A
  • Cutting depth: 25 mm
  • HF ignition / pilot arc
  • LED display
  • 5 m cable assembly

The plasma cutter impresses with a long duty cycle of 60 % at 90 A. To achieve a duty cycle of 100 %, the cutting current must be throttled to 69,7 A. The settings for plasma cutting are easy to control via the clearly-laid-out control panel.

Show more Show less

The cutting current of 20 to 90 A can be set using a continuous dial, the current value of which is clearly shown on the large LED display. The air pressure is also defined using a control knob and can be read via a pressure gauge. This allows you to effortlessly adjust both values—even when wearing welding gloves.

Show more Show less

Depending on the requirements, the air pressure for the torch cooling can be lowered via a valve. With a flow rate of up to 175 L air per minute, the air pressure can be up to 6 bar. The compressed air is used to create an electric air which cuts through a variety of metals and their alloys, such as stainless steel, copper, aluminium and titanium. Depending on the material, you can cut workpieces up to 25 mm thick. The plasma arc is ignited using the proven technology of high-frequency ignition.

Show more Show less

The plasma cutter S-Cutter 90 also scores points with its handling. The cut width of just 1,2 mm allows you to complete complicated work with low material wear. The 5 m-long cable between the power unit and the torch allows a great deal of freedom of movement when working on larger workpieces such as vehicles or heating systems.

Show more Show less

Efficient air cooling is one of the basic requirements for the high performance of the unit. The same applies to the switch-off device in the event of overheating. The coated sheet steel housing permanently prevents mechanical damage to the device components. The plasma cutter can be carried using a handy handle.

Show more Show less

  • High-performance—cut depth of up to 25 mm
  • Long-lasting—60% duty cycle at 90 A
  • Proven—high-frequency ignition for pilot arc
  • Precise—LED display for current
  • Easy operation—dials for air pressure and current

The plasma cutter with high voltage current cuts deeper

The plasma cutter S-Cutter 90 from Stamos Power

Model
S-CUTTER 90
Item number
10020129
Condition
New
Functions
Plasma Cutting
Rated input voltage
400 V / 3 phases
Frequency
50/60 Hz
Rated input current
14,7 A
Max. input current
19,1 A
Rated input power
9,5 kVA
Max. input power
12,6 kVA
Open circuit voltage
233 V
Ignition
HF
Cutting current
20 - 90 A
Operating time / duty cycle
60 %
Cutting current at 100% DC
69,7 A
Cutting current at 60% DC
90 A
Cutting torch (Ø connection)
P 80 (16 mm)
Cutting power
1 - 25 mm
Cutting width
1,2 mm
Air flow
240 L/min
Air pressure
4,5 bar
Power factor
≥ 0.85
Length, ground cable
3 m
Length, cable assembly
5 m
Length, power cable
2 m
Insulation class
F
Protection class
IP21
Device cooling
Fan
Dimensions (LxWxH)
54 x 28 x 46 cm
Weight
26 kg
Shipping dimensions (LxWxH)
68 x 46 x 52 cm
Shipping weight
36,2 kg
Technical drawing
Delivery Package
  • Plasma cutter S-CUTTER 90
  • Earth cable with clamp, 3 m
  • Cable assembly with plasma torch, 5 m
  • Cutting nozzle
  • Ceramic nozzle
  • Electrode
  • Gas line
  • Guide carriage
  • 2 clamp rings
  • Accessory bag
  • Instruction manual
 
IGBT

IGBT = insulated-gate bipolar transistor. IGBT is a bipolar transistor with an insulated gate electrode. This semi-conducting device is being increasingly used in power electronics because it combines the advantages of two transistor types: the easy controls of the field effect transistor and the fast switching and high breakdown voltage of the bipolar transistor. The IGBT also offers some robustness against short circuits because it limits the electrical continuity. IGBTs are a further development of MOSFET technology.

Show moreShow less
 
VENTILATORS

Powerful fans ensure an optimal removal of heat from the unit.

 
GAS/AIR CONNECTION

For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection.

Show moreShow less
 
EARTHING SYSTEM

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

 
GROUND TERMINAL CONNECTOR

 

 
CUTTING TORCH CONNECTION

 

 
SUPPLY VOLTAGE

This device works with a 3-phase connection (400 V +/- 10 %).

 
WELDING CURRENT

 

 
2-STROKE

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

 
PLASMA CUTTING

The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.

 
POWER SWITCH

 

 
DISPLAY

Shows the welding / cutting parameters.

 
OVERLOAD / FAULT LED

The LED light indicates overheating or a malfunction.

 
LOSS OF PHASE LED

The LED lights to indicate that the network connection of the phase has failed.

 
PRESSURE GAUGE (MANOMETER)

Shows the value of compressed air the compressor delivers to the plasma cutter. The plasma cutter has a pressure reducing valve which regulates the air pressure.

The following accessories can be used for the Plasma Cutter S-CUTTER 90 by Stamos Power:

Art. No.
Article
2124
Plasma Spare Parts Set - CUT 85 125 - H / CNC

Reviews from Stamos Expondo Expert ()

Is the plasma cutter easy to transport?

Yes, the device has a convenient handle for carrying.

How can I stay up-to-date on new products and offers?

Sign up for our newsletter and keep yourself up-to-date!

5 Based on 3 reviews

Sort by...

Leave a review
Evaluations will be activated after verification.

The fields marked with * are required.

Reviews from Amazon Customer (5 Oct 2019)
Reviews from Amazon Customer (5 Oct 2019) Reception dans le delais.... ! Je recommande.

Livraison et emballage excelent !Je recommande vivement.

Reviews from Amazon Customer (21 Jun 2019)
Reviews from Amazon Customer (21 Jun 2019) mes attentes ont ete depasser

decouper des pieces en inox et metal .il dise epaisseur 25mm ,j'ai reussi a decouper 40mm sans probleme

Reviews from Amazon Customer (18 Feb 2018)
Reviews from Amazon Customer (18 Feb 2018) Extremement satisfait!

Je n'écris que très peu de commentaire, mais ce produit en mérite un! Hors mis la livraison qui à été perturbé par la neige, ce plasma est vraiment pas mal! Bon c'est bien sur un produit d'import, pas de doute, mais les accessoires sont quand même remarquable. Un câble d'alimentation de 150cm, une durite d'air de 2m, câble de masse de 2m, et une torche de 3m peu être plus! Que demande le peuple! De plus le premier essaie est quand même assez concluant, il semble bien que les spé annoncé soit respecté...

expondo expert

Still not sure?

Our experts are ready to help!
+44 20 376 988 02
Mon - Fri 09:30am - 04:30pm
Einzelteile von Plasma Ersatzteilset - CUT 85 125 - H / CNC
59.00€
Prices incl. VAT plus shipping costs
Schweißhelm – Carbonic – PROFESSIONAL SERIES - 2987 - 1
99.00€
Prices incl. VAT plus shipping costs
This product
  • Cutting current: 20 - 90 A
  • Cutting depth: 25 mm
  • HF ignition / pilot arc
  • LED display
  • 5 m cable assembly

Ready to ship today,
Delivery time appr. 4-6 workdays

Plasma Cutter - 90 A - 400 V

Plasma Cutter - 90 A - 400 V

(3)
679.00€  

Ready to ship today,
Delivery time appr. 4-6 workdays

  • Cutting current: 20 - 90 A
  • Cutting depth: 25 mm
  • HF ignition / pilot arc
  • LED display
  • 5 m cable assembly
  • CNC plasma cutter
  • Cutting current: 20 - 85 A
  • Cutting depth up to 27 mm
  • Pilot arc
  • 2T/4T switch/ 400 V

Ready to ship today,
Delivery time appr. 4-6 workdays

CNC Plasma Cutter - 85 A - 400 V - pilot arc

CNC Plasma Cutter - 85 A - 400 V - pilot arc

(4)
669.00€  

Ready to ship today,
Delivery time appr. 4-6 workdays

  • CNC plasma cutter
  • Cutting current: 20 - 85 A
  • Cutting depth up to 27 mm
  • Pilot arc
  • 2T/4T switch/ 400 V