CNC Plasma Cutter - 85 A - 400 V - pilot arc

669.⁰⁰€ Prices incl. VAT

(7)

Preview: CNC Plasma Cutter - 85 A - 400 V - pilot arc

CNC Plasma Cutter - 85 A - 400 V - pilot arc

Play Video

360° photo

669.⁰⁰€

Prices incl. VAT

Free shipment to Ireland
?

Ready to ship today,
Delivery time appr. 4-7 workdays
30 days return service
?
3 years guarantee

Product highlights

CNC plasma cutter
Cutting current: 20 - 85 A
Cutting depth up to 27 mm
Pilot arc
2T/4T switch/ 400 V

The cutting current reaches 85 amps at its peak, which is achieved with a duty cycle of 60 percent. With a duty cycle of 100 percent, a high 65,8 amps are still possible. These performance values are sufficient to cut workpieces up to 27 millimetres thick. Cutting and quality cuts are no problem thanks to the high cutting speed and flash-start function. The professional plasma cutter S-PLASMA 85CNC offers you a wide range of features and outstanding characteristics that make it perfect for use in various CNC applications.

Show more Show less

The Stamos tool offers two different working modes so that maximum progress can be achieved with every task. In 2-stroke mode, the torch will run for as long as the power switch is pressed. In 4-stroke mode, a single tap is sufficient to activate the burner and another tap to switch it off. This mode provides countless advantages for continuous operation. The handle position on the torch can be varied during work to reduce fatigue and physical strain.

Show more Show less

The Stamos plasma cutter works with three-phase alternating current at an operating voltage of 400 V. Due to the modern design inside the CNC plasma cutter, disturbances such as interference of the high-frequency high-pressure arc are avoided or reduced. For this reason, this plasma cutter is particularly impressive in combination with a CNC machine and thus forms the perfect synergy.

Show more Show less

The torch is ignited via a pilot plasma arc. The compressed air for plasma cutting is set via a pressure reducer. Select the external compressor according to requirements and conditions. This makes the unit very flexible and easy to transport. To prevent oxidation or deformation on the workpiece after a cut, the air supply continues for a definable period of time. The run-on time can be set between 2 and 15 s directly on the power unit.

Show more Show less

The air is also cooled by the post-flow of the burner to avoid the risk of damage. The base unit is also equipped with a powerful fan cooling system to prevent overheating. However, if the operating temperature does experience a sudden increase, it will trigger the overheat protection.

Show more Show less

Problems with the operating temperature as well as other malfunctions are indicated by an LED on the control unit. The LED display for the cutting current and the cutting current controller are also located in this clearly visible space on the front of the unit. The cutting current can reach between 20 and 85 amps and is thus well above the performance data of the competition. With a product weight of 20 kilograms, the plasma cutter has sufficient mass to maintain safe footing even in a rugged working environment.

Show more Show less

CNC connection—ideal for CNC plasma cutting with high-quality CNC plasma cutting torch
Excellent performance values—85 amps at 60 percent duty cycle
Separate working modes—for short-term and continuous operation, powerful cooling of the power unit, the torch and the workpiece
Effective—pilot plasma arc ignition
Powerful—cutting depth of up to 27 millimetres
Precise—easy-to-read LED display

Plasma cutter with CNC plasma cutting torch

The plasma cutter S-PLASMA 85CNC from Stamos Germany is specially designed for professional use with CNC machines. It offers high-quality plasma technology in conjunction with functionality that is convincing in trade and industry. The plasma cutter impresses with special features such as a powder-coated sheet steel housing, high efficiency and first-class cutting quality.

Model

S-PLASMA 85CNC

Condition

New

Function

Plasma cutting

Input voltage

400 V three-phase

Input frequency

50 Hz

Rated input current

13,2 A

Max. input current

18,6 A

Rated input power

8,6 kVA

Max. input power

13,2 kVA

Load-free voltage

280 V

CNC

Yes

Cutting current

20 - 85 A

Duty cycle

60 %

Cutting current at 100 percent duty cycle

65,8 A

Cutting current at 60 percent duty cycle

85 A

Air post-flow time

2 - 15 sec

Housing cooling

Fan

Torch cooling

Air

Ignition

Pilot plasma arc

Length, grounding cable

4 m

Length, plasma cable

5 m

Length, compressed air hose

4 m

Length, power cord

3,8 m

Max. cutting depth

27 mm

Cutting depth for high-quality cuts

18 mm

Cutting width

1,2 mm

Air flow rate

175 L/min

Required air pressure

5,5 bar

Insulation class

Protection class

IP20S

Dimensions (LxWxH)

56 x 22 x 37 cm

Weight

20,7 kg

Shipping dimensions (LxWxH)

65 x 37 x 45 cm

Shipping weight

27 kg

Technical drawing

Download PDF

Manual

Download PDF

Delivery Package

Plasma cutter S-PLASMA 85CNC
Plasma cable assembly: 4 m
Air hose: 4 m
Grounding cable: 4 m
5 cutting nozzles
5 plasma electrodes
Ceramic cap for plasma
Ceramic ring
Pressure gauge and pressure regulator
Allen key
Hose cover
2 clamp rings
Instruction manual

IGBT

IGBT = insulated-gate bipolar transistor. IGBT is a bipolar transistor with an insulated gate electrode. This semi-conducting device is being increasingly used in power electronics because it combines the advantages of two transistor types: the easy controls of the field effect transistor and the fast switching and high breakdown voltage of the bipolar transistor. The IGBT also offers some robustness against short circuits because it limits the electrical continuity. IGBTs are a further development of MOSFET technology.

Show moreShow less

VENTILATORS

Powerful fans ensure an optimal removal of heat from the unit.

GAS/AIR CONNECTION

For plasma cutting, a gas is required with which the molten metal is blown away from the work surface. Compressed air is a common solution for this. For this purpose, the plasma cutter has a compressor connection.

Show moreShow less

EARTHING SYSTEM

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

GROUND TERMINAL CONNECTOR

CUTTING TORCH CONNECTION

SUPPLY VOLTAGE

This device works with a 3-phase connection (400 V +/- 10 %).

CNC CONNECTOR

The CNC connector is designed to connect the plasma cutter to CNC controls. Once connected, it will signal the THC module, which controls the height of the burner.

WELDING CURRENT

GAS POST-FLOW TIME

The time after the weld is finished in which gas continues to flow from the torch; this cools the burner and protects the weld from oxidation.

2-STROKE

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

4-STROKE

By pressing the torch button the solenoid valve opens. allowing the gas to flow in. The gas pre-flow ignites the arc at the pre-set current. Releasing the burner button initiates a rise in the current to that of the pre-set welding current. The welding process stops once you press the burner button again.

Show moreShow less

PLASMA CUTTING

The plasma arc melts the metal and the kinetic energy of the compressed air blows the metal aside.

POWER SWITCH

"2T / 4T" SELECTION SWITCH

Choose between the 2T and 4T mode.

DISPLAY

Shows the welding / cutting parameters.

OVERLOAD / FAULT LED

The LED light indicates overheating or a malfunction.

LOSS OF PHASE LED

The LED lights to indicate that the network connection of the phase has failed.

PRESSURE GAUGE (MANOMETER)

Shows the value of compressed air the compressor delivers to the plasma cutter. The plasma cutter has a pressure reducing valve which regulates the air pressure.

PILOT IGNITION

A pilot arc is ignited by pressing the torch's trigger. Thus, grates can be cut.

The diverse assortment of products from Stamos enable you to cut or join materials efficiently and precisely. Our portfolio ranges from professional soldering stations to top-class welding machines and precise plasma cutters, to the matching accessories. Let us demonstrate to you the functionality, quality and versatility – not to mention the cost-effectiveness – of our professional line. Our videos show our products in action.

How do I find a suitable welding hood?

You can find a wide selection of welding hoods from expondo under "Welders", in the subcategory "Welding Accessories".

How can I be sure that the accessories that are delivered with the welder are compatible?

When selecting the accessories, expondo places a strong emphasis on making sure that all components work perfectly together so that you can ensure the best possible welding results.

How can I stay up-to-date on new offers?

In order to keep up with the latest offers, simply subscribe to the newsletter from our website.

4 Based on 7 reviews

_{Sort by...}

Leave a review (5 stars is highest, 1 is lowest) ★ ★ ★ ★ ★

Click on the link sent to your e-mail address and confirm your opinion! It will be published after verification.

Reviews from Norbert Post (26 Mar 2022)

Reviews from Norbert Post (26 Mar 2022) Kraftvoller Schneidbrenner für Abbrucharbeiten

Der Plasmaschneider wurde angeschafft um eine große Doppelgarage in tragender Stahlbauweise zu zerlegen. Das hat er problemlos geschafft. An den Doppel T - Trägern wurden Materialstärken bis zu 20 mm durchtrennt. Manche Stellen waren nur mit etwas Abstand zu erreichen. Auch das hat er geschafft. Am Ende des Tages funktionierte die Düse immer noch, auch wenn man ihr jetzt die Arbeit ansah. Unser Leitungsschutzschalter löste beim Einschalten des Gerätes sofort aus. Gerät dann über den LS. eingeschaltet, und er lief problemlos weiter( B16 Automat). Einzig der Jeansstoff um den Brennerschlauch hat mehrere Löcher bekommen. Brennt m.M. nach zu schnell. Bin sonst sehr gut damit zufrieden.

Reviews from Norbert Post (25 Mar 2022)

Reviews from Norbert Post (25 Mar 2022) Guter Plasmaschneider, auch für Abrucharbeiten

Gutes Gerät das auch T-Träger zerlegt. Hier waren Materialstärken bis 20 mm vorhanden. Einzig der Hüllschlauch um das Brennerkabel (Jeanshose) brennt zu schnell. Luftschläuche habe ich anstelle der mitgelieferten Schraubklemmen mit quetschbaren Benzinschlauchklemmen befestigt. Das ist dann auch dicht.

Reviews from Anonym (12 Oct 2021)

Reviews from Anonym (12 Oct 2021) Top! Bon produit et délai respecté

Reviews from Jürgen (29 Aug 2020)

Reviews from Jürgen (29 Aug 2020) Gutes Gerät für einen einen super Preis

Habe das Gerät nun seit 1,5 Jahren und kann nichts schlechtes sagen. Es macht was es soll.
Ich habe den CNC Plasmaschneiden bei mir auf der CNC Anlage im Einsatz.
Natürlich ist es kein Hypertherm aber da liegt natürlich auch eine sehr große Preisdifferenz dazwischen.
Zur Leistung kann ich nichts negatives sagen, ich schneide damit auch 20mm dickes Stahlblech das schafft das Gerät auch ohne Probleme. Ich aus meiner Sicht kann es nur Empfehlen.

Reviews from Miloslav Tetour (2 Jul 2020)

Reviews from Miloslav Tetour (2 Jul 2020) nejlepší stroj v mém životě

je to rychlá práce radost s tím prqacovat

Reviews from S. Frischkopf (14 Jun 2020)

Reviews from S. Frischkopf (14 Jun 2020) Gerät hat nur 65A Leistung

Ich habe das Gerät vor einiger Zeit gekauft.
Leider musste ich bei einer Messung feststellen, dass das Gerät nur 65Ampere Schneidstrom hat.

Reviews from S. Frischkopf (8 Apr 2020)

Reviews from S. Frischkopf (8 Apr 2020) Fehlende Leistung

Ich habe das Gerät vor einiger Zeit gekauft und ausführlich getestet. Es ist an einer CNC Schneidanlage angeschlossen.

Pro:
-Auch nach vielen Stunden Einsatz, funktioniert das Gerät noch einwandfrei.
-Gute Einstellmöglichkeiten, kompakt.

Kontra:
-die mitgelieferten Luftanschlüsse sind nicht zu gebrauchen.
-Schon schnell bemerkte ich die fehlende Leistung. Ich erreichte nicht die gängigen Dicken / Schnittgeschwindigkeiten.
Also habe ich den Schneidstrom gemessen, es sind MAXIMAL 65 Ampere! und nicht 85 Ampere welche versprochen werden.
Es kann auch nachgerechnet werden. Schneidspannung x Strom = Leistung
140V x 65A = 9,1kW Leistungsaufnahme vom Gerät.

Wer nur bis ca. 8-10mm Material verarbeitet, kann das Gerät gebrauchen, darüber ist es nicht zu empfehlen!